Alunite grinding plant/powder processing plant

Alunite is a sulfate mineral, it occurs as veins and replacement masses in trachyte, rhyolite, and similar potassium rich volcanic rocks. It is formed by the action of sulfuric acid bearing solutions on these rocks during the oxidation and leaching of metal sulfide deposits. Alunite also is found near volcanic fumaroles. The white, finely granular masses closely resemble finely granular limestone, dolomite, anhydrite, and magnesite in appearance. The more compact kinds from Hungary are so hard and tough that they have been used for millstones.
Alunite can be used to make alum, potash fertilizer, sulfuric acid, and aluminium.
Alunite can be processed by Clirik Alunite grinding plant.
Performance and features of Clirik Alunite grinding plant:
1. High efficiency
Under the same final size and power, the product capacity of micro powder grinding mill is twice than jet mill and agitation mill.
2. Long lifetime of wearing parts
The roller and ring are made of special material, which improve the grinding efficiency a lot. For same material and final size, the lifetime of its wearing parts can reach to more than one year, about 2-5 times as long as that of vertical impact crusher and turbo-mill. Especially when handling calcium carbonate and calcite, the lifetime can reach 2-5 years.
3. High safety and reliability
There are no rolling bearings and bolts in grinding cavity, so problems caused by bolts shedding or wear of bearings and seal components will never happen.
4. High fineness of products
The product fineness can reach D97≤5μm.
5. Environment friendly
The application of DMC-120 pulse dust collector and muffler reduce the pollution and noise of the dust, which has reached national environment protection standard
Production Line Configuration of Clirik Alunite grinding plant:
The whole set HGM Clirik Alunite grinding mill consists of hammer crusher, bucket elevator, storage hopper, vibrating feeder, main unit, inverter classifier, cyclone collector, pulse deduster system, high pressure positive blower, air compressors and electrical control systems
Working Principle of Clirik Alunite grinding plant:
The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.

Technical Data of Clirik Alunite grinding plant:

Model	HGM80	HGM90	HGM100	HGM100A	HGM125
Ring Diameter(mm)	800	900	1000	1000	1250
Ring Number/pcs	3	3-4	3-4	4	4
Roller Number/pcs	21	24-32	27-36	27-36	40-44
Main Shaft Speed/r. p. min	230-240	200-220	180-200	180-200	135-155
Input Size/mm	≦15
Finished Size/um	5-47(325-3000)
Capacity t/h	0.4-4.5	0.4-5.5	0.4-6.5	0.4-7.5	0.7-10
Outlet Size L*W*H/m	13.9*4*6.2	14.7*4.8*7.2	18*4.6*8.6	18*4.6*8.6	14*9*10.25

Note: This specification is just referencing, any changes are subject to the products.